Not everyone wants to “add” parts to their new dirt bikes, which is fine, but for those that must tinker, we put together a “Top 5” must haves that we would recommend. We will be doing these “Top 5” articles with all of the new 450F/250F machines and will be splitting the information up between pulpmx.com and keeferinctesting.com. These mods are recommended, by us, through countless hours of testing. If you don’t find a specific aftermarket company that you prefer in this article, don't fret, email me at email@example.com and we can talk it out like adults should. Again, we will not push something on you unless we know it works. These mods that are in this article simply work for this specific machine.
Full Or Slip On Muffler System: The 2019 Suzuki RM-Z450 lacks a little bottom end and RPM response, so in order to get a little more of that the easiest thing to do is throw on a slip on or full muffler system. I am not going to sit here and tell you that you NEED a Pro Circuit Ti-6 system like the one that is on our test bike, but Joe Oehlhof (our test rider) says that the PC did help the lethargic feeling somewhat. Our “Average Joe” tester is no bullshit so I stand behind his findings. The PC system didn't “wow” us for initial RPM response at first, but we installed the insert into the muffler and that helped back pressure enough to create some more throttle response. Joe and I both liked the insert in for increased bottom to mid range throttle response without losing much top end pull. Installing this PC system helps with coming out of corners and also helps the Suzuki’s recovery time. With the stock system the recovery time out of corners (if you were a gear too high) was embarrassing for a 450cc machine. It would be hard to get back into the meat of the power forcing you to downshift and then immediately upshift, in order to get moving again quickly. With the PC system the rider can fan the clutch lever a couple times (in the higher gear) and it helps get the Suzuki on down the track in a quicker manner. The PC system is a step in the right direction for bottom and mid range pull. It doesn’t help or negatively affect the top end at all. Yes, we would still like a little more to make us happy. But wait… It does get better… Keep reading… www.procircuit.com
2. Ride Engineering Link: Simply installing the Ride Engineering link helped balance the RM-Z out on de-cel. If you’re running the stock suspension (valving/springs) this simple mod will help the RM-Z from wanting to transfer its weight towards the front end. The RM-Z450’s BFRC shock is known for unloading on de-cel (or riding high off throttle) and that can cause oversteer (knifing) on entrances of corners. Once you install the longer Ride Engineering link arms on the Suzuki it will settle down on de-cel and not pitch towards the front end as much. Running the sag at 107mm (fork height 4-5mm) with the link arm will alleviate some of your balance issues on the #RMaRMy. www.ride-engineering.com
3. Vertex Hi Compression Piston Kit: Installing a 13.5:1 Vertex piston kit helped get some added excitement out of Suzuki’s bottom to mid range. Stock compression is 12.5:1 on the RM-Z450, but bumping the compression up to 13.5:1 allows for us to still run pump fuel safely. Where you will notice the added pull is on deeply tilled tracks or soft tracks that force the rider to get on the throttle harder. The Suzuki now feels a little “spunkier”, “livelier”, and “more fun” to ride. It also helps the chassis feel lighter when the track is tighter or when it gets rougher. It allows the rider to “pop” over bumps and makes the Suzuki feel a little more playful. www.vertexpistons.com
4. Hinson Clutch Kit (Basket, Pressure Plate, Inner, Fibers, Steels, Springs): The stock clutch fades quickly during motos and the clutch lever actuation (engagement) is very narrow. Once the Hinson clutch kit was installed the feel of the clutch was more positive and less vague. The Hinson also took the improved bottom end we got from the muffler/piston and transferred that power better to the rear wheel. The stock mushy lever feeling was gone and a slightly stiffer firm feel replaced it. However, it wasn’t a “Honda hard pull” feel, just a slightly firmer/more positive than the stock Suzuki pull. We have been riding with the Hinson clutch for over a few months now and that feeling hasn't changed one bit. We also have to change our clutch plates less as the Hinson set up doesn't get burned up as quickly. www.hinsonracing.com
5. FCP Engine Mounts: If you still feel like the chassis is stiff during your late motos going to these mounts will help alleviate some of that harsh/sharp feeling through the headtube of the frame. I have tried these FCP mounts on most bikes and although they DO NOT work on every machine, I have found great results with them on the Suzuki RM-Z450. Immediately the front/top mounts got rid of some of the stiff bound up feeling of the chassis and allowed it to settle even more entering corners, stayed planted transitioning through the middle part of the corner, and allowed the suspension to absorb acceleration chop while keeping the rear wheel planted under acceleration. This was just another improvement from a simple bolt on part that gave me that secure feeling, to allow me to carry my momentum through corners and push the bike a little harder. Note: We tried just the top mounts first (for comfort/straight line stability) and then went to the front mounts for increased cornering (lean angle) ability. Use both for best results… www.fcpracing.com