Share This Article
I had the pleasure of getting invited to ride five new 2019 Husqvarna motorcycles (TC125, TC250, FC250, FC350, FC450) at the “Baker Factory” in Florida last week. Husqvarna held their 2019 world motocross introduction at Aldon’s lovely facility and let me tell you it is immaculate. The weather was hot and humid, but the track provided a great testing ground to give you some first impressions. Here are some things that I thought you would like to know about the 2019 Husqvarna line up, straight from the east coast.
All Of The New 2019 TC And FC Models Have:
Redesigned bodywork and graphics
Blue coated frame featuring increased rigidity
New 2-piece subframe design (250 g lighter)
Updated setting on the WP AER 48 forks
WP DCC shock featuring new piston & updated setting
Reworked SOHC cylinder head on the FC 450 (500 g lighter)
New cylinder head casting on FC 350 (200 g lighter)
Optimized timing on FC 250 exhaust camshaft
Machined finish on TC 125 & TC 250 upper exhaust port
Reinforced kick start intermediate gear on TC 125
New mufflers on 2-strokes, redesigned header pipe on TC 250
Chain adjustment length increased by 5 mm
New, stiffer upper triple clamp
Traction & launch control with updated settings [4-strokes]
New throttle cable routing for easier maintenance
Flow-designed resonance chambers & more compact silencers on 4-strokes
New generation Li-ion 2.0 Ah battery
Updated cooling system with new centre tube
New DS (diaphragm steel) clutch on TC 125, FC 250 & FC 350
ProTaper handlebar with new bend
Laser engraved D.I.D. wheels with new spoke nipples
New gearboxes produced by Pankl
TC 125/250 Two-Strokes: It’s not everyday that I swing my leg over a 125 and 250 two-strokes. The TC125’s engine is much improved since the last time I took it for a test spin. What I noticed about the TC125’s engine is that the jetting is very crisp and spot on. The TC125 barks and has great throttle response throughout the RPM range. However, the TC250 feels rich down low and doesn’t have that “crisp” feel out of corners like the little TC125 did. Both two-stroke machines have very light feeling chassis’s and can corner extremely well. The Baker Factory’s dirt was heavy as it had just rained the night before so the ruts were deep and long, but that didn’t phase these light weight TC’s. They both can lay over nicely in corners and have plenty of front wheel traction so you are able to cut down on those insides with ease. Vibration is not as apparent on the Husqvarna two-strokes like it is on the KTM’s. The KTM’s DO NOT have that much vibration, but it is apparent immediately that the Husqvarna’s just have less of it. Husqvarna uses a Pro Taper bar instead of a Neken, which to me helps the damping quality of the machines. The suspension on both machines felt soft to me. I am sure that if I was back in California, where the dirt is hard and choppy it would be better, but with the deep conditions of the Baker Factory the forks on both machines felt soft on de-cel bumps. Remember the dirt is extremely grabby on the east coast and adding a little air pressure to the AER fork and stiffening up the low speed compression on the shock will help you out. In this case going up 2 psi on the AER fork helped balance the pitching sensation out for me. I only had minimal time on each machine so a thorough test will just have to wait until I get my hands on my test bikes. At the end of the day if you asked me which bike is more fun to ride, I would have to tell you the 125 was more of a fun machine to rip around Aldon’s. Hitting ruts wide open and not letting off was something that put a pretty big smile on my face.
Husqvarna FC250: Husqvarna did a ton of work to the FC250 and it really showed especially in the engine department. I have always complained about lack of bottom end on the FC250, but now there is some added torque available for us lazy riders in 2019. I am not saying that the FC250 has YZ250F type bottom end, but at least now there is some excitement out of corners. The FC250’s engine still builds RPM’s calculated, but has a little better recovery time when I screw up on the track. A little stab of the clutch and the engine is very lively and pulls hard. You still have that great Husqvarna FC250 mid-top end pull and you are able to leave the white machine in second and third gear longer than the previous year model as well. The 2019 chassis is refined and although I didn’t feel as big of difference on the 19 FC250 (from the 2018) as I did the FC350 or FC450, it still gives me the confidence to charge bumps and rollers without giving me a wallow or heavy feel. Cornering is superb on the FC250 and feels light through corners and in the air. I think some of that light weight feel has something to do with a little more excitement from the engine, which always makes a bike feel lighter. Another aspect to the FC250 that I like a lot more this year is that it has less engine braking. Less engine braking means less pitching and a lighter more free-revving engine feel. This is huge when the dirt is soft like it is on the eat coast! The suspension on the FC250 feels balanced and soaks up smaller bumps better, but I still feel there needs to be more comfort in the fork on slap down landings. On slap down landings the WP AER fork feels harsh and doesn’t have the comfort a spring fork has.
Husqvarna FC350: Just last week I tested the KTM 350 SX-F and I can say the Husqvarna FC350 has mostly the same characters as the 350 SX-F. I say “mostly” because the FC350 doesn’t vibrate near as much as the KTM and the FC350 doesn’t have as much excitement down on low RPM like the KTM 350SX-F. The Baker Factory track that we tested on was tight and had long ruts, so the FC350 felt a considerably lighter than the FC450 did, even though there is only a few pounds difference between the two. The 2019 FC350 has more mid-range pulling power than the 2018, which is noticeable as soon as you roll the throttle on. It still doesn’t have the torque of a 450, but then again if you wanted to purchase a bike with loads of torque you wouldn’t be interested in the FC350 now would you? You have heard me talk about “engine recovery time” in other reviews and the FC350 has improved in that area as well. Just a small amount of clutch gets the FC350’s power back into what I like to call “the meat”. The meat is where the FC350 just sings and pulls you to the next corner or obstacle in a hurry. As light as this chassis feels on the 2019 FC350, it stays pretty damn straight (on-throttle). When accelerating out of long sweepers, the rear end stays more connected to the ground than last year’s model. The stiffer frame helps this contact feeling and is very noticeable under heavy load (which I actually got to test here at the Baker Factory being that the dirt is so good). I ran every FC and TC machine at around 105mm of sag and this seemed to be the happy spot where most of the machines felt balanced. The FC350’s suspension felt much like the 450’s in which both ends of the bike move together, give you a lot of traction and can handle hitting sizable braking bumps at speed. I made a huge mistake one lap, missed my braking point (into a corner), hit a big braking bump too fast and the FC350 just kicked a little and didn’t give me a big huck a buck like it would have in year’s past.
Husqvarna FC450: I am not going to sit here and lie to you. I think I put more time on the FC450 than any other bike here at the Baker Factory. Why, you ask? It’s actually quite simple. It is fast, yet easy as hell to ride! But 450cc’s is way too much for me Keefer? Unless you’re 125 pounds and a beginner, I am going to have to say “it isn’t too much for you”. The way the 2019 FC450 delivers its power is quite magical. If you’re worried about too much hit down low, don’t be, because the bottom end delivery is so smooth and easy to manage. Actually, I would want some more bottom end hit so I could pop out of these deep east coast ruts a little better at times. Back at home in California where the dirt is hard, this smooth delivery is what I am looking for, but back here where the dirt is heavy and wet you need some bottom end snap to get you on down the track ASAP. Even though the TC125 put a smile on my face, the FC450 put a bigger smile on my face due to its long pulling power and fun nature. The chassis is stable and predictable at speed, but still gives you a lightweight cornering feel. The suspension balance is good, but I am so spoiled with my WP Cone Valve/Trax shock set up (on my FC450 Rockstar Edition) that going back to the AER fork makes the Husqvarna feel slightly harsh on the very top of its stroke. When accelerating out of corners (when the fork is light and in the top of its stroke) the AER fork can deflect a little. This just gives a slight uneasy feel, but once off the gas the fork remains planted with a good amount of front wheel traction. The FC450’s ignition setting did have some slight de-cel popping, but maybe this was due to the high temps and high humidity in Florida. I usually don’t experience this on the west coast.
Blue Frame/Handguards: I am going to say this as nice as I can…Husqvarna please get your color scheme together. Blue frame, yellow fork guards, white plastic, black frame guards? Just when I really start to like the looks of the 2018.5 Rockstar Edition, you go and do this to me! Really?! The blue frame is dull and just looks tired too quickly for me. I would rather have a black or white frame to go with some yellow accents. Handguards? NO! I can understand why you are putting them on the FX line up, but we are moto guys! If I need handguards I will go purchase some at a later time. Handguards make the bike look fat and heavy and it’s not flattering to me. I am not a huge fan of the way the 2019 Husqvarna’s look, but I am going to give you guys a pass in 2019 because they work so well.
Baker’s Factory: To be able to come here and ride was something that only few will ever do. Aldon has built himself an immaculate area for riders to hone their craft. Between the work shops that you can eat off the floor, the perfectly mowed grass, the gym that smells like cotton candy and pink lemonade, the perfectly prepped tracks, this place is a dirt bike fanatic’s dream. The track that we got to test on was a mix of sandy clay and had huge ruts within an hour of riding on it. Testing a motorcycle here is optimal because you have the deep/heavy dirt for engine testing, dirt that provides big braking bumps and square edge for chassis/suspension testing. All of this gives you a well rounded testing facility to make any motorcycle better. After my day was done I walked back onto the track to really soak it all in. I looked at the lines that were formed and couldn’t believe how rough it got in a short amount of time. Not only did it get rough, but it kept high levels of traction throughout the day. Something in which California can’t offer riders.
Zach Osborne: Want to know how cool Zach-O is? He came out to both days of Husqvarna’s introduction and just hung out with the media guys. Not only did he do interviews, take photos and BS with everyone, he walked around the “other” track to help out the Rockstar Husqvarna team riders with their motos. Zach is just a down to earth guy that loves the sport as much as you or I.
Heat/Humidity: I know I am a west coast guy and you east coast dudes are used to this stuff, but holy crap it’s gnarly out here in Florida. I should of came out here to train for Loretta’s and I would of been so much better off. Being able to train in this stuff and ride national level type tracks is a such a huge advantage. On the day we were there testing Aldon had Marvin Musquin, Jordan Bailey, Mitchell Harrison and Michael Mosiman doing sprints and motos. To put in the work here at this facility will not only help you physically, but mentally as well.
East Coast/West Coast, Two Types Of Settings: I have listened to some of my testing media colleagues talk about taking these bikes back home to California to test them on our home turf. This statement doesn’t make sense to me at all and it drives me nuts as a test rider! Not every guy who purchases a Husqvarna lives in California right? Just because we are more comfortable on California dirt doesn’t mean “we” can’t give you (the reader) testing feedback on “your” kind of dirt. This is why I want to do an east and west coast 450 shootout this year. My California setting doesn’t work on Florida dirt/tracks and I know this. I also know there are thousands of people who want testing information on the east coast, not just the west coast. As test riders we are supposed to adapt to our test environment and try to give you the most honest feedback/setting that we can on the dirt we are provided, at the time of the test. We can’t just disregard where we are testing and expect to go back home and give you some “real world testing info”. Come on! We are at the Baker Factory, so that is why I am giving you some first impression testing feedback on these Husqvarna’s from this type of dirt.
